HomePick

Best Extractor Fans: Top Picks for Clean and Fresh Air

Are you in search of the most efficient extractor fans? This guide reviews the best extractor fan models you can buy within the UK.

Best Extractor Fan
READING TIME: 14 MINUTES

Are you in search of the most efficient extractor fans? This guide reviews the best extractor fan models you can buy within the UK.

Introduction to the Best Extractor Fans

Are you looking for the top extractor fans? This guide will help you find the top extractor fans you can purchase within the UK. We’ll discuss the benefits and specifications of each one along with their pros and cons, and the cost average.

The article will also cover the basics of the definition of an extractor fan and what it will cost to get an extractor fan fitted. This article can help you when you plan to purchase a new extractor fan.

What is an Extractor Fan?

Let’s first discuss what an extractor is. A fan that extracts unwanted air particles from space:

Extractor fans were created after the Second World War but did not gain commercial viability up until 1950 and the 1960s. Extractor fans serve to cleanse the air inside rooms like a bathroom or kitchen.

The principal function of extractor fans serves to ensure that the air inside the room is clean and to minimize the chance of health issues, such as allergies or harm to the space in general.

In addition to a bathroom or kitchen the extractor fan is designed for use in a utility room.

How Does an Extractor Fan Work?

Now, we’ll look at the operation of the extractor fan more in depth:

Extractor fans make use of suction to get rid of the smells, moisture and airborne particles. They then utilize an air vent to eliminate negative air from the room. A vent, such as windows will allow fresh, clean air to flow into the room.

Every kind of extractor fan comes with particular mechanisms, which we will go over in more depth in the following section.

When installing an extractor fan in the event that you are planning to modify the power circuit, or lighting system in the bathroom or kitchen you’ll have to inform the authorities of the local Building Control Department. Changes to electrical systems must comply with IEE regulations.

New cables or replacement cables could require RCD protection. The IEE rules divide a bathroom into hazard zones. Select a fan appropriate for the area in which you’re planning to install the fan.

Before you begin work, switch off the main electricity to prevent electrocution. In order to install the extractor fan you’ll first be required to determine the exact location where you’ll want it put in.

Utilize a pipe and cable detector to make sure there aren’t any hidden pipes or cables. Also, ensure that there aren’t any pipes on the outside of the wall that hinder the fan’s flow and there isn’t an outlet that is located just below the window.

Before Proceeding: you’ll need to wear a dust mask, gloves made of heavy-duty and ear protectors.

After: that, you can use a power hole saw to make a hole into the wall. The drill needs to be angled slightly upwards toward the inside. Cut the ducting into length using a small blade should it be required prior to fixing the fan’s body onto the ducting. The ducting and the fan should be pushed in the hole.

Follow the guidelines that are provided by the manufacturer in order to ensure that electrical cables are not pushed through.

Make holes to fix after marking them prior to fixing the fan. Take off the safety cover to inspect for electrical connections. An electrician is required to connect the final wires, in accordance with the manufacturer’s guidelines.

Install the grille cover inside. The slats should be in line to the ceiling. Finally, you must install the wall on the outside using external filler prior to installing the grille on the outside.

The steps in this article are general and what is needed will be determined by the type of extractor fan that is being used. It could be affixed to the ceiling, outside walls or inside the form of a window.

It will ultimately depend on the guidelines of the manufacturer. Bathrooms, kitchens, or utility areas are among the most suitable places for extractor fans to be placed.

Types of Extractor Fan

In this article, we’ll explore the various kinds of extractor fan, and lay their pros and pros and. This section will cover the axial, centrifugal and even inline extractor fan.

Axial Extractor Fan

Perhaps the most well-known kind of extractor fans are Axial fans. One of the main advantages of axial fans is their ability to move huge amounts of air to another place.

The fan’s blades move due to the motor that creates an air flow that is parallel to the motor’s axial. That is, you might have guessed, the reason for the term “axial fan” comes from.

Rotation of blades that allows an air flow can also generate the energy needed to improve the process. This is due to the fact that the kinetic energy reduces pressure on the blades and thus increases the extractor fan’s effectiveness.

The only drawback of Axial fans is the fact that they are unable to increase pressure and are quite loud in the event that you’re using the highest setting. In spite of that they are excellent when you require a device which can produce a huge airflow with low pressure.

It’s particularly helpful in reducing the temperature in an office or home space. Axial fans usually cost between £50 and £200.

Pros:

  • The price is not prohibitive.
  • Small and light.
  • Can move large air quantities.
  • Save on power bills when you compare it to other types of extractor fans.

Cons:

  • It can be loud.
  • Doesn’t contain high-pressure.

Centrifugal Extractor Fan

Also referred to as blowers, centrifugal fans can produce a high-pressure air flow. These extractor blades are arranged around an elongated hub.

The hub’s internal movement creates suction prior to pressure being established which causes air to be pushed to 90 degrees from the fan that extracts them.

If your home has the long-running pipe or ducts The high power capabilities of centrifugal fans could make them a suitable choice for you.

However the pressure is high, which means your energy costs will be higher, and in general centrifugal extractors can cost more than for instance an axial extractor.

In terms of positives, they are sturdy and less likely to be damaged due to large solid particles that have made it to the airflow.

There are a myriad of reasons that centrifugal fan technology is the most popular choice for mines. A Centrifugal fan is typically priced between £100-£300.

Pros:

  • High pressure.
  • Resilient.

Cons:

  • Energy and products are more expensive, as well as costs.
  • Bulky & heavy.

Inline Extractor Fan

Inline extractor fans are placed in the ceiling or loft space above the room they are installed in. The ducting connects the exhaust pipe with the grille outside that is situated beneath the eaves.

This fan is connected to the lighting circuit, meaning that every time the bathroom lights come on, so does the fan.

The job shouldn’t be too hard for an electrician, unless there’s any re-plastering or tiling work to be done once the extractor fan is installed. It’s a quiet and quiet option.

You could have several inline fans that are connected to maximize the rate of extraction for a particular space. An Inline fan can be purchased between £100 and £200.

Pros:

  • Discreet.
  • Low sound.
  • There may be several points from which air can be taken from.
  • Most often, they have powerful motors.

Cons:

  • Installation could be difficult, particularly in the event that additional work is needed.

Best Extractor Fan

An extractor fan’s lifespan is between 10 to 15 years. It is recommended to shut off the power prior to setting up an extractor. If you have any doubts you should consult a professional electrician.

In the end, certain aspects of the work require an experienced electrician, and it is recommended to consult an expert prior to the job in any way.

Manrose QF100TX5

The first fan we have that we have listed can be described as an axial fan, and an excellent budget choice. It has features like an over-run delay timer and backdraught shutter, and turning vane technology.

Although they aren’t expensive, Manrose extractor fans have been getting more popular in recent times. It is capable of removing 21 liters of air per second. Its power is just 7 watts. This gives it an energy rating of A class.

It is essential to locate the right location to install a Manrose extractor fan following the instructions of the manufacturer for installation.

After you’ve selected a suitable location, shut off the mains source. The QF100TX5 is designed for wires that are fixed only. Flexible cords cannot be employed.

The wiring must be completed correctly and there must be a minimum gap of 1 millimeter between the fan and cable inside this part. All wiring should conform to the IEE regulations.

A Double pole fused spur is required to be installed with a 3A fuse with minimum contact distance of 3 millimeters. There is no need to connect an earth because of the double insulation in the fan. After that, you will need to drill a hole in the ceiling or wall to be the location for the fan.

If you plan to attach your fan on the ceiling, be sure the hole is situated in between the two joists. Install ducting flush to the plaster. The fan’s cover can be removed by removing the two cover’s small screw caps.

The fan’s body should be placed against the ceiling or wall prior to marking the four screws and the cable entry point.

The fan must fit perfectly on the surface it’s mounted to. Install the power cable in its proper position. To run this timer model the fan requires the neutral, permanent supply as well as a switch live.

It is possible to make the fan operate by turning on and off in conjunction with an on/off switch, or by using the pull cord separately. The pull cord requires individual wiring. This extractor fan comes with an audio level of 27dB.

It is ideal for bathrooms as a top standard bathroom exhaustor. It is among the top extractor fans for bathrooms. It is possible to spend between £20 to £50 for this item which makes it quite affordable.

Pros:

  • Low-budget option.
  • Quiet extractor fan.
  • It also has the ability to run over time.

Cons:

  • The best bathroom design is more than, say, a kitchen.

EnviroVent Silent 100T

The axial extractor fan with a low sound is highly rated and a popular choice. The 100T features an incredibly high rate of extraction. It can extract 26 liters of air per second, which is roughly one meter of air per 60 minutes.

It’s IP4 and has an energy consumption of 8 Watts. Similar to the Manrose QF100TX5 it also has an over-run timer, which can be adjusted. It also comes with an adjustable backdraught shutter.

It can be used in zone 1 or 2 which have RCD protection. It is able to be attached to the ceiling or wall and discharge directly out to the outside or via the ducting system of a particular. You must make a hole at the spot you’ve chosen to install the installation of the 105mm. If you’re installing it with individual ducting, you’ll require an ordinary duct with 100mm diameter.

You must ensure that the flow of air won’t be hindered. Install the extractor on the wall to prevent noise from being generated and reduce the risk of damage happening.

Make sure that the backdraught shutter is functioning properly and is not damaged. Install the extractor fan on the wall by connecting the mains cables through the appropriate entry points for cable.

To wire the fan, you don’t require an earth connector since EnviroVent’s extractor fan has double insulation. Double pole switches having an opening of at least 3 mm away from the contact is required. The electrical cable must go through the 100T cable entry.

The wiring for the 100T has to be constructed in accordance with wiring rules. The timer for overruns must be in place. Last but not least, install the grille for protection. The instruction booklet from 

Envirovent provides additional information on the installation. It is a class B energy rating. It was given the Quiet Mark award in 2013 for its sound output of only 26.5dB.

It’s also the best design to be used in bathrooms. It is also covered by a five year warranty. This is probably the most efficient bathroom extractor. The 100T can be purchased costing somewhere between £30 or £40.

Pros:

  • Superb extractor fan.
  • A very popular option.
  • A particularly quiet option.
  • It also has an automatic timer for overruns.

Cons:

  • There is a requirement for 3 wires that isn’t suitable for every household.

Airvent 435103 Kitchen Extractor Fan

The next extractor fan is among the top alternatives for a kitchen. It is also suitable for a huge bathroom:

It is equipped with shutters that are automatically situated in front of the grille that are activated by thermal energy and have a built-in pull cord. The 435103 comes with an output that is 25W. For installation of this fan extractor, you must follow the instructions of the manufacturer. It has a noise at a level of 45 decibels. It also functions as an axial extractor.

The 435103 is equipped with an internal fan with a 150mm diameter inside the casing. It measures 21 cm x cm. Expect to be charged between £20 or £35 for this item.

Pros:

  • Don’t let air come back.
  • Durable pull cord.
  • The price is not too expensive.
  • Great extractor fan for the kitchen.

Cons:

  • A little edgy.
  • The information on the internet is not as extensive as other products in our selection.

Vent-Axia Silent Fan VASF100T

This fan is ideal for bathrooms that isn’t equipped with windows. The VASF100T is a popular model and has many favorable reviews on the internet.

It has back draught shutters, and two speeds that can be set while the fan is installed. It also comes with an attractive design. If you want to attach the VASF100T onto an existing ceiling or panel, it must be installed in an enclosed duct that has the protection of an air grille outside. The installation must be compliant with the local rules.

Create a hole of 105mm into the surface. Use two clips to push the lower part of the fan and then pull the grill away from its chassis.

The built-in spirit level will assist. Determine the centers of the screws by using the holes on the rear plate on the fan. Screw, drill and plug the back plate in place.

After installation, ensure that the impeller turns without difficulty and the shutter can be opened easily. Replace the grille and make sure that the clips are activated.

To mount the wall the hole’s diameter should be around 115mm. Make a hole in the wall, then put in the wall sleeve. Be sure the sleeve is slightly angled towards the downwards and away from the extractor fan. Cut the length to fit before putting the wall in an alignment flush with the sides on the walls. The clips should be pushed to the lower part of the fan and remove the grille from the chassis.

The screw holes should be marked as you would do for an installation on a ceiling. Use the built-in spirit level to aid you. Plug, drill into the hole and secure the backplate into place. Install the grille on the outside in position with the louvers pointed towards the downwards. Make sure the impeller is able to rotate freely. Don’t forget to activate the clips.

It is equipped with high-efficiency motors and creates just 14dB of audio. This is the best product to be used in bathrooms. Again, this fan has an axial. The VASF100T is covered by a two year warranty. This extractor fan can cost you between £35 or £45.

Pros:

  • Very popular and highly rated.
  • Back draught shutters.
  • Perfect for bathrooms with no windows.
  • Exhaust fan with high-end quality for bathrooms.

Cons:

  • Not a good fit for all rooms.

Manrose 22693 Extractor Fan

This extractor fan by Manrose is an additional extractor fan that is perfect for kitchens. The fan measures 250mm and has an extract rate of 300m3/h. It comes with a long-lasting ball bearing motor, and it is constructed using the use of high-gloss ABS thermoplastics.

The reason for the fan is to provide fans with a long-lasting and strong design and also make it fairly simple to wash.

It can be used with a maximum pressure of 50 p.a. The 22693 has similar installation instructions as the QF100TX5 but in this case it is fitted with a ball bearing drive.

Follow the instructions of Manrose to install the extractor fan when it comes to installation. It is able to produce 40dB of sound. It is the best choice for the kitchen. It is possible to purchase this fan for around £30 or £40.

Pros:

  • Installation is easy.
  • The price is not too expensive.
  • A low energy consumption level.

Cons:

  • A little big.
  • It does not include ducting.
  • It does not have an integrated shutter.

Vent-Axia 17104020 ACM100T

The ACM100T Another product manufactured by Vent-Axia can be a good example of an extractor in line. It’s a very silent option which comes with a detachable motor core, an adjustable over-run timer, and a two speed motor that can be controlled. It is, however, very costly with this.

To install the ACM100T, first, use an X-headed screwdriver to take out those two plastic clippings, by removing the two bolts that are on the fan. The motor impeller assembly is then pushed out. Then, place an extractor fan on whatever angle you prefer by using the holes provided. The base has to be fixed correctly prior to taking an impeller motor assembly into its place.

Then take the screw off and tighten. This will hold the screw in place. The next step is wiring. Remove the terminal box cover as well as its screws. Place them on the side. In this case you’ll have to wire it in accordance with the directions provided with diagrams provided by Vent-Axia.

It’s essential to check all connections to make sure that all is correct and all clamps for cables as well as terminals are securely in place. The entry of the cable must be completed by using the cable grommet which is provided with this item.

Last but not least, replace the screws and terminal box cover, and make sure that the impeller is able to rotate freely and is not in any way hindered in any.

The ACM100T is equipped with an audio level of 23dB. It’s ideal for a bathroom, kitchen or utility rooms. This is possibly the most efficient inline extractor fan on the market, and certainly one of the top. It is possible to purchase the Vent-Axia extractor fan at around £90 or £130.

Pros:

  • Particularly, low levels of sound.
  • Includes an overrun-timer.
  • It comes with a two speed motor that can be selected.

Cons:

  • Very expensive.

Cost to Install an Extractor Fan

After you’ve selected an extraction fan you’ll have an expert to put it in the right place:

For an extractor fan that is newly installed it is possible for the labor cost to come at around £200. The cost to have an old fan replaced, it will cost around £100 for labour expenses.

It is also important to think about the price of the equipment itself and any other expenses, for example, the cost of disposal in the event that you’re replacing an old fan.

Benefits of an Extractor Fan

In this article, we will look at the many advantages of using extractor fans:

Controlling Fumes, Steam & Odour

In the kitchen, bathroom or utility room, unwelcome or unhealthy air can be eliminated with extraction fans. A gap, such as windows, can let fresh, clean air flow into the room.

If you have the recirculation extractor it will refresh the air and then circulate it throughout the space. Recycling or removing moisture reduces the possibility of water damage that could result in the growth of mold.

The elimination of odors and smells is beneficial to your perception of the space however it is also important for health reasons. Long-term exposure to various pollutants could cause illnesses in the course of time.

Controlling Humidity

Controlling humidity is essential to avoid the growth of mildew and mold. Similar to reducing steam, which can aid in this regard and control humidity, so too can reducing steam.

Although some products may temporarily get rid of a room mildew and mold, if there isn’t the proper humidity control issues are likely to recur time and time again.

Heat Removal

A further benefit of extractor fans is their ability to take out heat. It is common for heat to rise and spread upwards towards the ceiling. Therefore, an extractor is able to take hot air out of the room, allowing cool air flow within the room.

RELATED ARTICLES

Scroll to Top